Railways USB Chargers

Home> Products> Chargers > Railways USB Chargers

Input voltage range

12 Vdc +/-30%

12Vdc, 24Vdc +/- 30%, 48Vdc -30% +25%

12Vdc, 24Vdc,+/- 30%, 48Vdc -30% +25%

17-32Vdc

24-32Vdc, 12-16Vdc. Configured to prevent depletion of source battery.

5Vdc using main 230Vac input power adaptor (supplied)

9-32Vdc

9-32Vdc (Automatic Referencing)

Auto-Select, 85-135Vac and 170-265Vac, 50/60Hz

Output Power

2.1A (single) 3.0A (double) - max 1.5A per socket

As stated, taken for a maximum of 2 minutes followed by 8 minutes rest.

Wireless Charger: Nominal 5W; USB Charger: 10W for BC1.2 and 12W for Q.C 3.0

Transient voltage protection

EN50121-3-2 to EN61004-4

Meets EN50155: 2007, EN50121-3-2: 2006

Meets ISO7637-2 International standard for 12/24V vehicles

Meets ISO7637-2 International standard for 24V vehicles

Meets ISO7637-2 International standard for 24Vdc commercial vehicles

Output noise

<100mV pk-pk at continuous load.

<50mV pk-pk

<50mV pk-pk (100mV on 24V units) at continuous load. Meets CISPR25

<50mV pk-pk (100mV on 24V units) at continuous load. Meets CISPR25 and VDE0879-3

<50mV pk-pk (100mV on 24V units) at continuous load. Meets CISPR25.

<50mV pk-pk at continuous load

<50mV pk-pk at continuous load. Meets CISPR25

Storage Temperature

-25 ºC to +100ºC

-25?C to +100?C

-25ºC to +100ºC

-25ºC to +70ºC

Casework

Anodised aluminium, glass filled polycarbonate, dust water and impact resistance to IP533

Anodised aluminium, glass filled polycarbonate, dust water and impact resistance to IP533. Ruggedised versions also available to IP65

Anodised aluminium, glass-filled polycarbonate, dust water and impact resistance to IP533.

Anodised aluminium, glass-filled polycarbonate, dust, water and impact resistance to IP655

Anodized aluminium, glass-filled polycarbonate

Black polycarbonate body

Dark grey polycarbonate body

Grey polycarbonate body

Polycarbonate body

Silver anodised aluminium, glass filled polycarbonate

Mounting Method

?Click ?n? Fit? mounting clip or rubber feet. DIN rails clips available required

‘Click ‘n' fit mounting clip, fitted separately using 3 hole fixing (4 hole on 400W and 600W)

‘Click ‘n' fit mounting clip, fitted separately using three hole fixing

‘Click ‘n’ fit mounting clip, fitted separately using three hole fixture or use of two DIN rail clips

‘Click ‘n’ fit mounting clip, fitted separately using three hole fixture, *4 hole cradle

‘Click ‘n’ Fit’ mounting clip or rubber feet. DIN rails clips available required

30mm diameter hole with or without bezel. USB2 for non through fitting applications

30mm diameter hole, secured by rear nut or front-fitting bezel

Box with mounting screw holes - screws provided. Can also be installed by clips or other bespoke method

By rubber feet on base and direct attachment to radio above

Click ‘n’ fit mounting clip, fitted separately using three hole fixture

Click ‘n’ fit mounting clip, fitted separately using three hole fixture **4 hole cradle

Enclosure with underside securing plate into Ø80mm hole

PT10/20 tie wrap to wiring (supplied) PT40/60/100/200 3off half inch No8 pozi pan head screws (supplied)

Overvoltage and Undervoltage

Limited by sensing circuit

Transients

Protected by filters and rugged component selection

Approvals

2014/30/EU The general EMC directive 2014/35/EU The low voltage directive 93/68/EEC The CE marking directive

2014/30/EU The general EMC directive 93/68/EEC The CE marking directive AES5, ECE R118.02 and UL 94: V-0

2014/30/EU The general EMC directive Regulation 10 The automotive directive 93/68/EEC The CE marking directive

2014/30/EU The general EMC directive Regulation 10 The automotive directive 93/68/EEC The CE marking directive AES5

2014/30/EU The general EMC directive Regulation 10 The automotive directive 93/68/EEC The CE marking directive AES5, ECE R118.02 and UL 94: V-0

IP Ratings

IP30

IP65 (Not USB connector)

IP65 when installed correctly

PVPro IP30; PV65R IP65; PV6i-R & PV12i-R IP53

Output voltage

110% for 10s 200% for 1s 300% for <0.5ms On over current shutdown there is a retry every 30s

12V

12V or 24V nominal through the intelligent battery charging curve. Please see charge graph for further information.

13.6 Vdc. Worst case limits are +/- 4%,108W (9A)

13.6Vdc +15% -20% at extremes of temperature, load, input tolerance, etc.

13.6Vdc or 27.2Vdc +15% -20% at extremes of temperature, load, input tolerance, etc.

13.6Vdc or 27.2Vdc+15% -20% at extreme temperature, load, input tolerance, etc.

24V

27.2Vdc +/-5% at extremes of temperature, load, input tolerance, etc.

48V

5Vdc +/- 0.2V

Nominal 5W

Application

Charges all QI qualified devices

Charges all USB devices including Apple and Android

Charging of wireless enabled devices

Directable reading light for installaion in seat back

Wireless Charger: Charges wireless enabled devices; USB Charger: Charges all USB devices inc. Apple and Android

Vibration / shock

EN61373

EN61373: 2010

Power Conversion Efficiency

-25ºC to +30ºC to meet this specification table+30ºC to +80ºC de rate linearly to 0A

50%-60%

90%

Light on 98mA @ 12V, 48mA @ 24V

Typically 83%

Typically 85%

Typically: 85%

Typically: 90% for non-isolated units, 85% for isolated units

Typically: 90% for non-isolated units, 85% for isolated units ** 95%

Typically: 90% for non-isolated units, 85% for isolated units, *95%

Typically: 93%

Wireless Charger: 50%-60%; USB Charger 90%

Operating humidity

100%

95% max, non-condensing

95% max., non-condensing

Connections: Input Output Ground

4 core cable, *4 wires (1m in length) stripped and tinned for individual connection

Five 6.3mm push on flat blade connectors

Five 6.3mm push-on flat blade connectors

Five 6.3mm push-on flat blade connectors 6-way 070 connector (PV12s-A)

Four 6.3mm push on flat blade connectors (72-240W) Five terminal connector with screw tightening with mating half supplied (400W and 600W units)

Four 6.3mm push-on flat blade connectors

Four 6.3mm push-on flat blade connectors, *5 way Phoenix connector including enable on/off terminal and mating half

IEC-320 C14 socket, C13 terminated cordset 6.3mm push-on blade terminals 6.3mm push-on blade terminals, adjacent to input (additional external ground if required)

Input: 6.3mm push-in flat blade connectors On/off switch incorporated

Input: 6.3mm push-in flat blade connectors Output: USB type 'A' single socket - tested to 10,000 mating cycles

Input: 6.3mm push-in flat blade connectors Output: USB type single/double socket - tested to 10,000 mating cycles

Input: 6.3mm push-in flat blade connectors Output: Wireless transmission <200kHz

Input: Power supply plug Output: Wireless transmission <200kHz

Safe area protection: Over Current

Limited by current sensing circuit

Reverse Polarity

Limited by sensing circuit

Catastrophic failure

Internal fuse

Protected by input and output fuses

Protected by internal input and output fuses

Markings

CE and E (automotive) marked

CE and E marked

Filters Sort results

Reset Apply

Select	Name	Image	Price	Varations	Buy
	12/24VDC IP65 USB CHARGERS FOR RAILWAY APPLICATIONS		$43.45-$349.18		Add to cart

Railways USB Chargers

Online Store

Sectors

Catalogs

About

Follow Us

This website uses cookies to ensure you get the best experience on our website, by clicking OK you also accept the terms of service and our privacy policy.